View HDM30-12B-D05_4464669.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

H HiTRON
PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES 30 WATTS SINGLE OUTPUT HDM30-S SERIES
FEATURES:
SINGLE OUTPUT WIDE 4:1 & 2:1 INPUT RANGE 30W ISOLATED OUTPUT SIX-SIDED SHIELD
SPECIFICATION
INPUT SPECIFICATION
Input Range: Wide 4:1 & 2:1 DC input range. See Ratings Chart. Input Voltage: Nominal 12/24/48Vdc. Input Current: Various with input range and load. See Ratings Chart. Input Fuse: Use external fuse. Input Filter: Pi-Network. Overvoltage Shutdown: Optional. Factory set. Undervoltage Shutdown: 8Vdc. Isolation Resistor: 1,000 Mega Ohms. Isolation Voltage: 1,500Vdc. EMI: Six-sided metal shielding. Remote On/Off: TTL/CMOS-Compatible Input Control. (Voltage refer to the -Input) Positive Logic version for Standard set up: ON(Enable)=Open(or 2.5-5.0Vdc above-Vin). OFF(Disable)=Short(or 0-0.8Vdc above-Vin). Negative Logic version option available by adding a "N" suffix to the end of Model #.
OUTPUT SPECIFICATION
Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Voltage Accuracy: Main O/P 2.0% typical. Line Regulation: Various with input & output voltages. 0.5% typical. Load Regulation: Various with output voltages. 1.0% typical. Noise & Ripple: Typical 100mV for 3.3V/5.0V & 1.0% for others peak to peak. OVP: Built-in on main output. Overload Protection (OLP): Fully protected against output overload and short circuit. OLP set at about 125-150% rating output wattage. Consult the factory for OLP setting. Operating Temperature: -10 to +70C range. 0C to +60C full load without derating. From +60C, derating linearly to half load @+70C.
(Refer to Derating Chart.)
GENERAL SPECIFICATION
Efficiency: 81% typical various with input. Switching Frequency: Fixed frequency 100K Hz. Circuit Topology: Forward Circuit. Transient Response: Peak deviation 200mV, Recovery time < 3mSec.@ 25% step load change. Case: Black coated copper with non-conductive metal base. Power Density: 10 Watts. / Cubic inch. MTBF: Type 1,000,000 hours to Mil. Std.217, 25C.
Temperature: -20C to +85C. Temperature Coefficient: 0.02% /C. Cooling: Convection cooling up to +60C @ full load. At least 100LFM moving air is recommended for full load > +60C in a confined area. Humidity: Up to 95%RH, Non-condensing. Commercial Grade only.
NOTE: (1) All measurements are at nominal input, full load, and +25C unless otherwise specified. (2) Line Regulation measured from High to Low Lines at full load. (3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input. (4) Correct fuse size by calculating the max. DC current drain at low Line input & Load and then adding 20-25for the desired fuse size.
Due to requests in market and advances in technology, specifications subject to change without notice.
-27-
INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART
SINGLE OUTPUT MODEL NO.
INPUT Vdc INPUT CURRENT N. L. (mA) F.L.
2300 2700 2650 2750 2800 3100 1150 1350 1325 1375 1400 1550 575 675 662 687 700 775 1175 1375 1350 1400 1425 1575 587 687 675 700 712 787
OUTPUT VO1(Vdc) @
3.3V 5.0V 9.0V 12.0V 15.0V 24.0V 3.3V 5.0V 9.0V 12.0V 15.0V 24.0V 3.3V 5.0V 9.0V 12.0V 15.0V 24.0V 3.3V 5.0V 9.0V 12.0V 15.0V 24.0V 3.3V 5.0V 9.0V 12.0V 15.0V 24.0V
OUTPUT VO1(A)
6.40A 5.00A 2.80A 2.20A 1.80A 1.25A 6.40A 5.00A 2.80A 2.20A 1.80A 1.25A 6.40A 5.00A 2.80A 2.20A 1.80A 1.25A 6.40A 5.00A 2.80A 2.20A 1.80A 1.25A 6.40A 5.00A 2.80A 2.20A 1.80A 1.25A
CASE SIZE
DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A
HDM30-12B-S03 9.0HDM30-12B-S05 9.0HDM30-12B-S09 9.0HDM30-12B-S12 9.0HDM30-12B-S15 9.0HDM30-12B-S24 9.0HDM30-24B-S03 18.0HDM30-24B-S05 18.0HDM30-24B-S09 18.0HDM30-24B-S12 18.0HDM30-24B-S15 18.0HDM30-24B-S24 18.0HDM30-48B-S03 36.0HDM30-48B-S05 36.0HDM30-48B-S09 36.0HDM30-48B-S12 36.0HDM30-48B-S15 36.0HDM30-48B-S24 36.0HDM30-24D-S03 9.0HDM30-24D-S05 9.0HDM30-24D-S09 9.0HDM30-24D-S12 9.0HDM30-24D-S15 9.0HDM30-24D-S24 9.0HDM30-48D-S03 20.0HDM30-48D-S05 20.0HDM30-48D-S09 20.0HDM30-48D-S12 20.0HDM30-48D-S15 20.0HDM30-48D-S24 20.0Symbols: "" OVP built-in.
30 18.0 30 18.0 30 18.0 30 18.0 30 18.0 30 18.0 20 36.0 20 36.0 20 36.0 20 36.0 20 36.0 20 36.0 15 72.0 15 72.0 15 72.0 15 72.0 15 72.0 15 72.0 30 36.0 30 36.0 30 36.0 30 36.0 30 36.0 30 36.0 20 72.0 20 72.0 20 72.0 20 72.0 20 72.0 20 72.0 "@" Adjustable.
MECHANICAL DIMENSIONS: MM [INCHES]
PIN NO. PIN #1. PIN #2. PIN #3. PIN #4. PIN #5. PIN #6. PIN #7. PIN #8. PIN #9. PIN #10.
WEIGHT: 156.0g (5.6 Oz.) PIN ASSIGNMENT
SINGLE Remote ON/OFF +INPUT -INPUT/-Vin NO PIN NO PIN OUTPUT TRIM NO PIN +VO1 DC-COM NO PIN
DERATING CHART
CASE SIZE: DM2A
-28-
H HiTRON
PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES 30 WATTS DUAL OUTPUT HDM30-D SERIES
FEATURES:
DUAL OUTPUT WIDE 4:1 & 2:1 INPUT RANGE 30W ISOLATED OUTPUT SIX-SIDED METAL SHIELD
SPECIFICATION
INPUT SPECIFICATION
Input Range: Wide 4:1 & 2:1 DC input range. See Ratings Chart. Input Voltage: Nominal 12/24/48Vdc. Input Current: Various with input range and load. See Ratings Chart. Input Fuse: Use external fuse. Input Filter: Pi-Network. Overvoltage Shutdown: Optional. Factory set. Undervoltage Shutdown: 8Vdc. Isolation Resistor: 1,000 Mega Ohms. Isolation Voltage: 1,500Vdc. EMI: Six-sided metal shielding. Remote On/Off: TTL/CMOS-Compatible Input Control. (Voltage refer to the -Input). Positive Logic version for Standard set up: ON(Enable)=Open(or 2.5-5.0Vdc above-Vin). OFF(Disable)=Short(or 0-0.8Vdc above-Vin). Negative Logic version option available by adding a "N" suffix to the end of Model #.
Remark: Logic voltage refer to -Input (-Vin)
OUTPUT SPECIFICATION
Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Voltage Accuracy: Main O/P 2.0% typical. Line Regulation: Various with input voltages. 0.5% typical. Load Regulation: Various with output voltages. VO1 1.0% typical. VO2 2.0% typical. Noise & Ripple: 100mV for 3.3V/5.0V & 1.0% typical for other output peak to peak. OVP: Built-in on main output. Adjustability: VO1 O/P may optionally be external trimmed 3.0% with a fixed resistors or trim-pot. Overload Protection (OLP): Fully protected against output overload and short circuit. OLP set at about 125-150% rating output wattage. Consult the factory for OLP setting.
GENERAL SPECIFICATION
Efficiency: 76- 81% typical, various with input & output voltage. Switching Frequency: Fixed frequency 100K Hz. Circuit Topology: 100K Hz. Forward Circuit. Transient Response: Peak deviation 200mV, Recovery time < 3mSec. @ 25% step load change. Case: Black coated copper with non-conductive metal base. Power Density: 10.0 Watts. / Cubic inch. MTBF: 1,000,000 hours to Mil. Std. 271, 25C. Operating Temperature: -10C to +70C range. 0C to +60C @ full load without derating. From +60C, derating linearly to half load@+70C.
(Refer to the Derating Chart).
Temperature: -20C to +85C. Temperature Coefficient: 0.03% /C. Cooling: Convection cooling up to +60C @ full load. At least 100LFM moving air is recommended for F-L > +60C in a confined area. Humidity: Up to 95%RH, Non-condensing. Commercial Grade only.
NOTE: (1) All measurements are at nominal input, full load, and +25C unless otherwise specified. (2) Line Regulation measured from High to Low Lines at full load. (3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input. (4) Correct fuse size by calculating the max. DC current drains at low Line input & Load and then adding 20-25% for the desired fuse size. Due to requests in market and advances in technology, specifications subject to change without notice.
-29-
INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART
DUAL OUTPUT
MODEL NO. HDM30-12B-D05 HDM30-12B-D12 HDM30-12B-D15 HDM30-24B-D05 HDM30-24B-D12 HDM30-24B-D15 HDM30-48B-D05 HDM30-48B-D12 HDM30-48B-D15 HDM30-24D-D05 HDM30-24D-D12 HDM30-24D-D15 HDM30-48D-D05 HDM30-48D-D12 HDM30-48D-D15 INPUT Vdc 9.0- 18.0 9.0- 18.0 9.0- 18.0 18.0- 36.0 18.0- 36.0 18.0- 36.0 36.0- 72.0 36.0- 72.0 36.0- 72.0 9.0- 36.0 9.0- 36.0 9.0- 36.0 20.0- 72.0 20.0- 72.0 20.0- 72.0 INPUT CURRENT OUTPUT (Vdc) N.L. (mA) F.L. +VO1@ -VO2 30 2,670 +5.0V -5.0V 30 2,500 +12.0V -12.0V 30 2,590 +15.0V -15.0V 20 1,560 +5.0V -5.0V 20 1,525 +12.0V -12.0V 20 1,525 +15.0V -15.0V 20 780 +5.0V -5.0V 20 763 +12.0V -12.0V 20 763 +15.0V -15.0V 40 1,350 + 5.0V - 5.0V 40 1,265 +12.0V -12.0V 40 1,310 +15.0V -15.0V 30 800 +5.0V -5.0V 30 775 +12.0V -12.0V 30 775 +15.0V -15.0V
"" Double Feedback.
OUTPUT (A) +VO1 -VO2 2.50A 2.50A 1.00A 1.00A 0.83A 0.83A 3.00A 3.00A 1.25A 1.25A 1.00A 1.00A 3.00A 3.00A 1.25A 1.25A 1.00A 1.00A 2.50A 2.50A 1.00A 1.00A 0.83A 0.83A 3.00A 3.00A 1.25A 1.25A 1.00A 1.00A
CASE SIZE DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A
Symbols: "" OVP built-in.
"@" Adjustable.
MECHANICAL DIMENSIONS: MM [INCHES]
WEIGHT: 156.0g (5.6 Oz.) PIN ASSIGNMENT
PIN NO. PIN# 1. PIN# 2. PIN# 3. PIN# 4. PIN# 5. PIN# 6. PIN# 7. PIN# 8. PIN# 9. PIN# 10. DUAL Remote ON/OFF + INPUT -INPUT/-Vin NO PIN +VO1 DC-COM -VO2 OUTPUT TRIM NO PIN NO PIN
DERATING CHART
CASE SIZE: DM2A
-30-
H HiTRON
PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES 30 WATTS TRIPLE OUTPUT HDM30-T SERIES
FEATURES:
TRIPLE OUTPUT WIDE 4:1 & 2:1 INPUT RANGE 30W ISOLATED OUTPUT SIX-SIDED METAL SHIELD
SPECIFICATION
INPUT SPECIFICATION
Input Range: Wide 4:1 & 2:1 DC input range. See Ratings Chart. Input Voltage: Nominal 12/24/48Vdc. Input Current: Various with input range and load. See Ratings Chart. Input Fuse: Use external fuse. Input Filter: Pi-Network. Overvoltage Shutdown: Optional. Factory set. Undervoltage Shutdown: 8Vdc. Isolation Resistor: 1,000 Mega Ohms. Isolation Voltage: 1,500Vdc. EMI: Six-sided metal shielding. Remote On/Off: TTL/CMOS-Compatible Input Control. Positive Logic version for Standard set up: ON(Enable)=Open(or 2.5-5.0Vdc above-Vin) OFF(Disable)=Short(or 0-0.8Vdc above-Vin) Negative Logic version option available by adding a "N" suffix to the end of Model #.
Remark: [Voltage refer to -Input (-Vin)].
OUTPUT SPECIFICATION
Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Voltage Accuracy: Main O/P 2.0% typical. Line Regulation: Various with input voltages. 0.5% typ. Load Regulation: Various with output voltages. VO1 & VO3 2.0% typical. VO2 5.0% typical. Noise & Ripple: 100mV for 3.3V/5.0V & 1.0% typical for other output peak to peak. OVP: Built-in on main output. Adjustability: VO1 O/P may optionally be external trimmed 3.0% with a fixed resistors or trim-pot. Overload Protection (OLP): Fully protected against output overload and short circuit. OLP set at about 125-150% rating output wattage. Consult the factory for OLP setting.
GENERAL SPECIFICATION
Efficiency: 78-81% typical, various with input & output voltage. Switching Frequency: Fixed frequency 100K Hz. Circuit Topology: 100K Hz. Forward Circuit. Transient Response: Peak deviation 200mV, Recovery time < 3mSec. @ 25% step load change. Case: Black coated copper with non-conductive metal base. Power Density: 10.0 Watts. / Cubic inch. MTBF: 1,000,000 hours Mil.Std.271, 25C. Operating Temperature: -10C to +70C range. 0C to +60C @ full load without derating. From+60C derating linearly to half load@+70C.
(Refer to the Derating Chart).
Storage Temperature: -20 to +85C. Temperature Coefficient: 0.03% /C. Cooling: Convection cooling up to +60C @ full load. At least 100LFM moving air is recommended for full load > +60C in a confined area. Humidity: Up to 95%RH, Non-condensing. Commercial Grade only.
NOTE: (1) All measurements are at nominal input, full load, and +25C unless otherwise specified. (2) Line Regulation measured from High to Low Lines at full load. (3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input. (4) Correct fuse size by calculating the max. DC current drains at low Line input & Load and then adding 20-25% for the desired fuse size. Due to requests in market and advances in technology, specifications subject to change without notice.
-31-
INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART
TRIPLE OUTPUT
MODEL NO. HDM30-12B-T5/12 HDM30-12B-T5/15 HDM30-12B-T5/+12,-5 HDM30-24B-T5/12 HDM30-24B-T5/15 HDM30-24B-T5/+12,-5 HDM30-48B-T5/12 HDM30-48B-T5/15 HDM30-48B-T5/+12,-5 HDM30-24D-T5/12 HDM30-24D-T5/15 HDM30-24D-T5/+12,-5 HDM30-48D-T5/12 HDM30-48D-T5/15 HDM30-48D-T5/+12,-5
Symbols: "" OVP built-in.
INPUT Vdc 9.0- 18.0 9.0- 18.0 9.0- 18.0 18.0- 36.0 18.0- 36.0 18.0- 36.0 36.0- 72.0 36.0- 72.0 36.0- 72.0 9.0- 36.0 9.0- 36.0 9.0- 36.0 20.0- 72.0 20.0- 72.0 20.0- 72.0
INPUT CURRENT OUTPUT (Vdc) N.L. (mA) F.L. +VO1@ +VO2 -VO3 50 2,550 +5.0V +12.0V -12.0V 50 2,550 +5.0V +15.0V -15.0V 50 2,500 +5.0V +12.0V - 5.0V 40 1,520 +5.0V +12.0V -12.0V 40 1,550 +5.0V +15.0V -15.0V 40 1,420 +5.0V +12.0V - 5.0V 40 760 +5.0V +12.0V -12.0V 40 775 +5.0V +15.0V -15.0V 40 710 +5.0V +12.0V - 5.0V 60 1,325 +5.0V +12.0V -12.0V 60 1,325 +5.0V +15.0V -15.0V 60 1,300 +5.0V +12.0V - 5.0V 50 785 +5.0V +12.0V -12.0V 50 800 +5.0V +15.0V -15.0V 50 735 +5.0V +12.0V - 5.0V
"" Double Feedback. "" Stacked on main O/P.
OUTPUT (A) +VO1 +VO2 -VO3 2.5A 0.5A 0.5A 2.5A 0.4A 0.4A 2.5A 0.5A 1.0A 3.0A 0.6A 0.6A 3.0A 0.5A 0.5A 3.0A 0.6A 1.0A 3.0A 0.6A 0.6A 3.0A 0.5A 0.5A 3.0A 0.6A 1.0A 2.5A 0.5A 0.5A 2.5A 0.4A 0.4A 2.5A 0.5A 1.0A 3.0A 0.6A 0.6A 3.0A 0.5A 0.5A 3.0A 0.6A 1.0A
CASE SIZE DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A DM2A
"@" Adjustable.
MECHANICAL DIMENSIONS: MM [INCHES]
WEIGHT: 156.0g (5.6 Oz.) PIN ASSIGNMENT
PIN NO. PIN# 1. PIN# 2. PIN# 3. PIN# 4. PIN# 5. PIN# 6. PIN# 7. PIN# 8. PIN# 9. PIN# 10. TRIPLE Remote ON/OFF +INPUT - INPUT/-Vin NO PIN +VO2 DC-COM -VO3 + VO1 NO PIN OUTPUT TRIM
DERATING CHART
CASE SIZE: DM2A
-32-

▲Up To Search▲

Price & Availability of HDM30-12B-D05

	To Download HDM30-12B-D05 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .